(0 Remaining)
Welcome to the TMS Knowledge Base
This page can help give you answers to all of the questions that you have flying around in your head. If you can't find what you're looking for then you can "ask a new question", and within a few hours, you will receive an answer from one of our TMS specialists. Your question can be about anything that is Thermal Store related, including solar energy, wood burners and underfloor heating systems.


Search Knowledge Base:   
Your search has found 43 results.
1)  How can I get a good answer to my problem?
2)  Is it better to have a flat panel solar collector or evacuated tubes?
3)  What's the difference between a Wood Burner and a Wood Boiler?
4)  Why would I choose to have an underfloor heating system over radiators?
5)  Which cylinder material is the better, stainless steel or copper?
6)  Wood Burner rising flow return thermo syphon problems and External Quench cooling unit solution
7)  What about hard / soft water issues ie calcium deposits or limescale buildup?
8)  What is the cylinder insulation heat loss?
9)  Solar flat plates or evacuated tubes?
10)  What is a ThermalStore?
11)  How do the 2 stage twin DHW coils and mixer work
12)  Thermal mass of underfloor heating concrete or screed?
13)  How best to design DHW hot water distribution pipework and pumped secondary curcuits
14)  Can you explain the benefits of choosing thicker cylinder insulation and how it effects
15)  Hi There, Do you have information/a comparison of the best pipe lagging technologies out there. Ideally, something that connects cost to insulative qualities and perhaps ease of obtaining/fitting. thanks!
16)  What does head and flow mean when sizing a pump
17)  Rant from TMS technical
18)  Sizing your Thermal Store Cylinder
19)  Sizing Boilers
20)  Wood gravity thermo syphon and do i need an external quench unit
21)  Are there any diagrams for full systems and the required associated plumbing?
22)  What is a Class A pump Class B pump
23)  Solar drain down, direct, series, parallel and east west roof
24)  I cannot afford - dont have the time or money to fit everything right now
25)  I'm interested in purchasing a thermal store but I have read online that they are referred to as sludge buckets. What does this mean and is it true?
26)  Mains pressure coil or PHE plate heat exchanger?
27)  how to wire 3 immersion elements
28)  How does the solar flume work
29)  What temperature should i set the electric immersion heater elements
30)  In your described system you state that the solar collectors are also filled with the fernox liquid, ie part of the direct system. How does this work when the collectors may freeze in the winter? Or do they drain down
31)  What does the cylinder custom positioning entail?
32)  the smart pumps have several modes on them LPP, HPP, LCP & HCP. What should they be set to for Underfloor and central heating?
33)  How do I connect my solar PV iBoost/Immersun to 3 immersion connections on thermal store?
34)  I have an issue with floor joist weight loading of cylinder
35)  what is meaning or the difference between direct and indirect
36)  combi boilers converting existing of choosing new system boiler
37)  What is Zoning Control?
38)  Underfloor UfH manifold sizing issues
39)  F&E Expansion tank - What head height do i need for my gas boiler
40)  Radiators and solar panels are above the header F&E tank
41)  How do i know if i have enough mains pressure
42)  Sun angles see http://www.sunearthtools.com
43)  Is it possible to quantify the reduction in oil boiler use in the following scenario: Wood burning stove and oil boiler using a thermal heat bank assuming a wood burning stove is run for 4 hours per evening with the demand for central heating the next morning for 3 hours?
» Click Here to Show All Questions/Answers  Advanced Search (more results)